基于参数预标定的长行程PMLSM无传感器控制

为了解决长行程定子不连续永磁直线同步电机存在的因无法全程安装位置传感器和不同动子和定子之间的电磁参数不固定所造成的控制性能下降的难题,提出一种在每一段定子内先进行参数标定,再进行速度控制的控制系统设计。首先,在动子进入过程中,对电机进行电磁参数标定,根据标定参数对控制器参数进行调整,以达到更好的控制效果。然后,使用无位置传感器控制系统使动子快速达到设定速度值并稳定运行。实验结果表明:动子进入过程参数标定精度分别为0.002Wb和0.000 4H;无位置传感器控制中位置估计精度为0.63mm,速度收敛时间为0.45s,稳态误差为0.02m/s。基本满足永磁直线同步电机用于长行程运输的控制快速性、稳定性等要求。     

Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

谐振变换器的ZVS软开关同步整流技术研究

以感应电能传输(IPT)谐振变换器为研究对象,研究了谐振变换器的ZVS同步整流(SR)技术。分析了基于SR技术IPT谐振变换器的工作原理,利用系统的谐振工作特性,提出了一种新颖的ZVS软开关SR实现方法。建立了系统频闪映射稳态数学模型,给出了ZVS软开关SR的周期不动点函数、数值求解状态变量及ZVS软开关SR工作周期的算法流程。在设计控制电路的基础上,通过实验验证了提出的同步整流技术的可行性。     

基于DSP的多元数据同步采集与存储系统的设计与实现

从硬件和软件两个角度出发,介绍基于DSP的多元数据同步采集与存储系统的组成、工作模式以及功能的测试。系统主要由上位机和数字采集与存储单元组成,其中数字采集与存储单元的硬件部分包括电源模块,值班电路模块,数据采集模块,数据存储模块,时钟同步模块。系统采用DSP作为中央处理芯片,利用经过同步后的秒脉冲作为触发信号,实现同步数据采集。以CF卡作为存储介质,实现数据自容式存储。软件部分实现自检、同步、数据采集存储功能。经过测试,系统工作稳定,功能正常,同步精度在100ns以内。     

新型复合式内部能量集成的精馏塔的机械设计与水力学模拟

基于HIDiC的理论和Aspen 模拟的结果，建立了新型内部能量集成的精馏塔的塔节结构，对筛孔式结构的复合HIDiC塔节做了CFD模拟，探索了不同参数下的水力学性能，优化了新型复合塔节的结构。结果表明：对于筛孔式复合塔节，减小塔板孔径，降低出口堰高有利于提高传质和传热效果。利用SolidWorks软件针对温度与压力下的双重效应做了静应力分析，通过HIDiC理论，模型构建，水力学模拟相互验证，将HIDiC逐板换热的理论与实际模型完美结合。     

Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results.      

The relationship between perceptions of an innovative environment and creative performance in an online synchronous environment

This study focused on the relationship between perceptions of an innovative environment and creative performance in a web-based synchronous environment. A total of 160 sophomores and juniors from the National Taiwan Normal University participated in a learning activity consisting of a pretest and posttest quasi-experimental design. Pearson’s correlation coefficients and analysis of covariance (ANCOVA) were used in data analysis. Results indicated a positive correlation between personal creative performance and a free, supportive, and innovative environment. Team support and organizational obstruction had less influence on personal creative performance. Compared with a traditional classroom, a synchronous environment added to innovative essence and helped learners do better in terms of novelty, feasibility, value, and creative product design overall.     

A Restart Control Method for Position Sensorless PMSM Drive Systems Without Potential Transformer for Railway Vehicle Traction

This paper proposes a restart control method for position sensorless PMSM drive systems without a potential transformer for railway vehicle traction. This method can estimate the initial rotor speed and position under coasting conditions over the entire speed range. The method can also be used when the back‐EMF voltage is higher than the inverter DC link voltage. The proposed method is verified by experiments using a 200‐kW PMSM.     

Calculation of the Characteristics of Salient‐Pole Synchronous Machines Assisted by Permanent Magnets on the Basis of the Operating Principle

In this study we investigate a method for accurately calculating the characteristics of salient‐pole synchronous machines assisted by permanent magnets. First, the operating principle of the machines is investigated by using both finite element analysis and a simple magnetic circuit. Then, a theoretical representation of the assist effect on the permanent magnets is derived based on the magnetic circuit. Finally, the measured and calculated results are compared in order to confirm the validity of the proposed calculation method. We show that the load characteristics of the proposed machine can be accurately estimated from the no‐load and short‐circuit characteristics of the conventional machine without permanent magnets, and the size and magnetization of the inserted permanent magnets.